New Construction. Vertical Rail Control. The Full Bodysurfing Setup.

The POD WOW 13" Handboard, PF2 Swim Fins, Neoprene Fin Socks, and Fin Savers with Heel Protectors cover every contact point for the experienced bodysurfer. The WOW 13" is a polyurethane handboard with an 18mm concave base and integrated keel fin. The PF2 is the most structured fin in the PF Series, with vertical rails that keep the legs stable on the wave face. The fin socks refine the fit inside the foot pocket. The fin savers and heel protectors secure the connection at the ankle. Four products, four specific jobs.

POD WOW 13" Bodysurfing Handboard

The WOW 13" is a 330mm polyurethane handboard with a weight, density, and rigidity profile tuned for lightweight durability and flex rebound. The 18mm concave base with integrated mono-keel fin channels water flow to support lift and directional hold through the wave. The convex palm hold deck supports a natural hand position and reduces strain across longer sessions.

The polyurethane construction is crack-resistant and suited to regular surf use across a wide range of conditions without the maintenance requirements of a timber board.

For full product details visit the POD WOW 13" Handboard page.

PF2 POD Swim Fins

The PF2 is the most structured fin in the POD PF Series. Made from natural Malaysian buoyant rubber, it carries vertical rails that extend to the blade edge, improving wave hold and keeping the legs from sliding down the wave face. The sole ramp-up reduces unnecessary toe movement and improves comfort under load. The symmetric Chisel Blade® and Splay Rails® distribute load evenly and support controlled, directed movement through the water.

The PF2 suits swimming, open-water training, bodysurfing, bodyboarding, kneeboarding, lifesaving, and ocean photography across a wide range of conditions.

For full product details visit the PF2 POD Swim Fins page.

PF2 Swim Fin Sizing

For the most accurate fit, use the measurements below or the POD Fit Finder on the PF2 product page.

Step 1 - Foot Length and Width

Small: 6-7 - Length 23 cm, Width 8.5 cm
Small/Medium: 7-8 - Length 24 cm, Width 9 cm
Medium: 8-9 - Length 25 cm, Width 9.5 cm
Medium/Large: 9-10 - Length 26 cm, Width 10 cm
Large: 10-11 - Length 27 cm, Width 10.5 cm
Extra Large: 11-12 - Length 28 cm, Width 11 cm
Measurements are maximum sizes before stretch.
Natural rubber stretch allowance up to 5 mm for a snug fit

Step 2 - Ankle Strap Width

Small: 8.2 cm
Small/Medium: 8.7 cm
Medium: 9.3 cm
Medium/Large: 9.5 cm
Large: 10 cm
Extra Large: 10.5 cm
Measurements are before stretch.
Strap stretch allowance of 10-15 mm for a secure, non-slip fit
View the PF2 foot and ankle size chart here

POD Neoprene Fin Socks

The POD 3mm Neoprene Fin Socks use a registered stitch-free inner arch construction. The inner arch is left smooth rather than stitched, removing the most common source of discomfort associated with standard fin socks. The sock naturally hugs the medial arch of the foot without irritation. Suits feet that sit on the lower end of the fin pocket range, or where added warmth and protection in cooler water is needed.

Neoprene Fin Sock Sizing

Small: 6-7
Medium: 7-9
Large: 9-10
Extra Large: 10-12
Extra Extra Large: 12-14

For full product details visit the POD Neoprene Fin Socks page.

POD Fin Savers and Heel Protectors

The POD Swim Fin Savers and Heel Protectors use a single streamlined ONE-Strap webbing connection between the ankle and the rubber fin strap. That single strap reduces the bulk and drag associated with wider webbing systems. Soft neoprene heel pads wrap around the fin strap to prevent chafing, stabilise the heel, and improve retention in surf, shore break, and moving water.

For full product details visit the POD Swim Fin Savers and Heel Protectors page.

Care - Handboard and Swim Fins

Fresh water rinse after every surf - handboard, fins, socks, and savers
Shade dry only - avoid direct sunlight for extended periods
Avoid direct heat - never leave gear inside a vehicle on a hot day
Store correctly - lay the WOW handboard flat and keep fins upright to maintain shape

Heat warning - do not leave handboard or fins in sun or hot car

POD fins are manufactured for use within the stated and engraved size range. Using a size more than one size below the specified size alters the intended foot-to-blade ratio and may result in an improper fit or reduced function. Fitting fins to feet larger than the stated size may cause overstretching or overloading, which can compromise the structural integrity of the fin. Such misuse voids warranty coverage. POD rubber fins are made for swimming and are not intended for walking or running. Bending or flexing the blade beyond 35° in any direction may cause tearing or cracking of the blade or sole. Damage resulting from such actions is not covered under warranty. To minimise the risk of damage when moving in shallow water, fins should be used for swimming only. Avoid walking or running forward while wearing fins. Where movement on land or in shallow water is necessary, walking backwards will help prevent undue stress to the blade and foot cavity. This warranty does not affect your rights under the Australian Consumer Law.